NeilPryde would like to use cookies to store information on your computer to improve our website and to enable us to advertise to you those products and services which we believe may be of interest to you. One of the cookies we use is essential for parts of the site to work and has already been sent. You may delete and block all cookies from this site but some elements may not work correctly. To find out more about the cookies we use, please refer to our privacy policy.OK

Language

Search

RS:Flight Sail

Foiling / Freerace

High performance sail based on RS:RACING design and specifically developed to perform both on Windfoil and Slalom boards. The RS:FLIGHT is an evolution of the RS:RACING LT1 sail, and is designed on the concept of real world racing combined with key foiling features. Compared to a pure racing sail, the RS:FLIGHT has a higher aspect ratio, shorter boom and increased foot size to accommodate vertical rake when foiling. The sail delivers quick and precise response instantly allowing the rider to adjust the power by sheeting in or out to control the flying height on the foil. The RS:FLIGHT brings a combination of excellent top-end speed, enhanced bottom-end power, superior control and stability to a wide range of performance minded sailors.

Colors:

  • C1

Highlights

Twist Shaping Concept


The twist shaping concept incorporates powerful, forward-oriented lower body profile together with increased twist and profile reduction in the mid-body area of the sail. This concept retains power and acceleration while at the same time increases the release in the lower leech area. As a result, the new R:FLIGHT can be sailed with more rake angle, increasing lift on the fin and improving top-end acceleration and speed. At the same time head twist is controlled in order to keep consistent pressure on the mast foot and prevent the nose of the board from lifting in gusts.


Pronounced Leading Edge
Increased leading edge curvature generating constant drive and high acceleration in gusts.

Tip Vortex Reduction
Induced drag reduced thanks to unrestricted head batten twist.

 

Progressive Aspect Ratio


RS:FLIGHT features progressive aspect ratios across different sail sizes in order to address the specific functionality. Higher aspect ratio in larger sizes (7.8 and up) increases light wind efficiency and performance of the rig as well as improving maneuverability at the marks by reducing the boom length. Lower aspect ratio in smaller sizes (7.0 and down) helps maintain top-end control and stability by focusing the sail center of effort around the rider area where it is easier to control.

 

Dual Boom Length Dynamic Compact Clew


The dual boom length options, allows for the rider to adapt the sail's performance to various conditions. Outer clew position can be used when you are looking for extra power and upwind lift while the inside clew setting provides better power release and control. Those performance adjustments are made possible by the outer position supporting (locking) the lower leech twist for increased power, while the inner position allows the lower leech to twist freely making it release excessive power while locking the draft forward.

 

Seamless Leading Edge


The evolution of component sleeve construction completely eliminates the front seam along the sail leading edge. This increases precision during the assembly process, reduces weight at the leading edge, creates a perfectly clean profile entry and eliminates a weak spot in construction at the exposed leading edge by removing any stitching that could come in contact with the mast.

 

Component Sleeve Construction


Combining materials with specific properties in the RS:FLIGHT sleeve allowed us to achieve optimum profile entry stability and elasticity, critical for rotation and light weight. Front section (1) is made from Luff Glide woven material that has the necessary elasticity and durability to resist wear from direct mast contact. A low stretch Dyneema™ ArmourWeb section (2) can take high downhaul tension and is critical in stabilising the profile entry, providing smooth bridging between Ultra Cams. Tetoron is used for central-rear part of the sleeve (3) as this material combines elasticity, durability and light weight. Elasticity is critical to keep soft rotation as well as improves pumping performance in light wind.

 

Quadruple Luff Panel Layout


RS:FLIGHT features four continuous luff panels that carry most of the sail body shaping. This configuration stabilises the critical section draft position while also providing lightweight yet stretch-resistant way of increasing the film thickness proportional with downhaul load distribution. Continuous panels eliminated horizontal seams crossing the highly loaded leading edge, which increases response of the sail as well as durability. Introduction of this extremely stable leading edge platform that is able to take very high downhaul loads allowed us to integrate Clear Pocket construction in the remaining sail body.

FEATURES

1Mini Batcams

Dual Tube Batten

6Three-Piece Cam Battens

2Carbon Leech
Mini Battens

9Batten Chafe Protection

7Kevlar Batten Bridges

8Aerodynamic Boom cutout closure

3Loopsters

4Batcam Screw Adjuster

Clew Batten

Single Tube RDM Batten

Single Tube RDM Batten

5 Mini Carbon Battens

Three-Piece Cam Batten

Two-Piece RDM Tube Cam Batten

 

1 Mini Batcams

Streamline and reduce weight in critical upper leech.

2Carbon Leech Mini Battens

Provide max support with minimum weight.

3Loopsters

Allowing easy rigging through loop to loop system that reduces the friction and eliminates any crossing lines (crucial when using adjustable outhaul system).

4Batcam Screw Adjuster

For easy and precise tension application.

5Mini Carbon Battens

For a smoother leading edge in the upper area where no cams are used.

6Three-Piece Cam Battens

A 3-piece batten provides the framework for the design of a smooth, lightweigh and stable sail profile.
A. Carbon/fiberglass tube: stiffest section
B. Hollow mid-section: medium stiffness
C. Precision Tapered CNC Batten: variable stiffness

7Kevlar Batten Bridges

To distribute the high downhaul load crossing the battens.

8Aerodynamic Boom cutout closure

Prevents the apparent wind from blowing into the mast sleeve and generating drag.

9Batten Chafe Protection

Abrasion resistant PU print to help protect the battens from damage caused by rigging or boom contact.

103x Ultracams

Innovative suspended camber system dramatically improves sail rotation and acceleration out of gybes.
Simultaneous tuning of battens and cambers makes the sail easy to tune.

11Clear Pocket Batten Sleeve

Overlapping body panels create a sleeve for battens, eliminating the need for traditional, separate batten pockets. This saves on unnecessary weight, simplifies construction and creates a fully symmetrical batten cavity, eliminating the tendency of traditional batten pockets to load differently from one tack to another.

 

Sail Specs

SizeLuffBoomBaseBattensCamsIdeal Mast
5.4 416 163-169 16 8 3 400RDM
6.2 446 185-190 16 8 3 430
7.0 469 195-200 10 8 3 460
7.8 492 205-210 32 8 3 460
8.6 517 215-220 28 8 3 490
9.4 543 227-232 14 8 3 520